Tab Content
  • boman's Avatar
    Yesterday, 05:04 PM
    boman replied to a thread Noisey GE dryer in Appliance Repair
    Yes, when normal wiring harness is used, it is the nomal set up with 220/240 volts. The test cord is only 110/120 volts. With normal wiring...
    5 replies | 100 view(s)
  • boman's Avatar
    08-14-2019, 06:11 AM
    boman replied to a thread Noisey GE dryer in Appliance Repair
    No using 110-120 volt test plug. Throwing me off since the motor normally runs on 110-120 volts. Even more so that it sounds okay with the test cord...
    5 replies | 100 view(s)
  • boman's Avatar
    08-13-2019, 08:26 PM
    boman started a thread Noisey GE dryer in Appliance Repair
    Ge Model - DVLR223EG1WW New one for me. Dryer sounds as if the motor bearing are shot. Removed the motor and ran on cheat wire. Three...
    5 replies | 100 view(s)
  • boman's Avatar
    08-01-2019, 06:01 PM
    Will do if I decide to fool with it more. I think someone before me put the wrong roller supports on it. The two on the rear bulkhead are the...
    12 replies | 811 view(s)
  • boman's Avatar
    07-30-2019, 07:35 AM
    Thanks Jeff. I was thinking one was supposed to be a little longer. The exploded diagram I looked at (I thought) showed them to be the same in the...
    12 replies | 811 view(s)
  • boman's Avatar
    07-29-2019, 06:32 AM
    I sort of suspected s screw hitting the drum and turned one around so the head of the screw was to the inside. Swapped a couple of rollers around....
    12 replies | 811 view(s)
  • boman's Avatar
    07-28-2019, 09:28 PM
    https://youtu.be/7fwKqqSc4sk
    12 replies | 811 view(s)
  • boman's Avatar
    07-28-2019, 07:56 AM
    On my phone. I will check it on a laptop. I did upload a short video of it on YouTube Sent s link to you Jeff. Hope you get it.
    12 replies | 811 view(s)
  • boman's Avatar
    07-27-2019, 06:49 AM
    boman started a thread Dryer elements in Appliance Repair
    How necessary is it for an electrical dryer element to read around 12 or 14 ohms resistance? Seems I have had them work that just showed continuity....
    1 replies | 147 view(s)
  • boman's Avatar
    07-27-2019, 06:41 AM
    “Solder sucker.” Agreed. I don’t have one right now. Plan to try small braided wire to help get the solder off. Btw, this is concerning...
    7 replies | 497 view(s)
  • boman's Avatar
    07-27-2019, 06:36 AM
    Second from the right is 3 dots. No option there that I can see. Anyway, got to thinking about it and remembered some retry good dents on the...
    12 replies | 811 view(s)
  • boman's Avatar
    07-26-2019, 07:09 PM
    Sorry, thought I might post a video of this dryer running. I do not see the option. Model- GEQ9800PW0 Thumping noise. Rollers? Felt seal? ...
    12 replies | 811 view(s)
  • boman's Avatar
    07-26-2019, 07:02 PM
    Bought s new soldering iron. Just going to remove them. Hope this be does better than the ones I had been trying to use. Better point and more...
    7 replies | 497 view(s)
No More Results
About boman

Basic Information

Statistics


Total Posts
Total Posts
102
Posts Per Day
0.63
General Information
Last Activity
Yesterday 05:04 PM
Join Date
03-16-2019
Referrals
0