Help spread the word / share us on your favorite social media networks

Facebook Twitter StumbleUpon Reddit LinkedIn

Maytag Neptune TopLoader washing machine water extracting issues

Maytag Neptune TopLoader washing machine water extracting issues

Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: Maytag Neptune TopLoader washing machine water extracting issues

  1. #1
    Join Date
    Nov 2014
    Posts
    7

    Default Maytag Neptune TopLoader washing machine water extracting issues

    I have a Maytag Neptune Top loader washing machine. It seems that when the setting for spinning (water extracting) the tube makes a noise and the clothes are still wet when spin cycle is complete. I know the controll panel is basically a mother board and I have changed that 2 years ago. Since then the water that flows into the softener spot doesnt work along with the bleach dispenser. Any sugestions would be greatly appreciated.


    Kwall139

  2. #2
    Join Date
    Feb 2012
    Location
    Canada
    Posts
    2,348

    Default

    Hi,

    Maytag Neptune TopLoader washing machine
    Model#?
    http://www.applianceaid.com/model-number.php Some model# helps.

    It seems that when the setting for spinning (water extracting) the tube makes a noise and the clothes are still wet when spin cycle is complete.
    The ?wash tub? makes a noise but doesn't spin? Is all the water gone at the end of the cycle?

    I have changed that 2 years ago. Since then the water that flows into the softener spot doesnt work along with the bleach dispenser.
    Started right after your repair?...if yes, no one considered you may have a defective part or maybe a wrong part?

    jeff.
    http://www.applianceaid.com/
    Appliance Repair Aid

  3. #3
    Join Date
    Nov 2014
    Posts
    7

    Default

    The was tub extracting issue and dragging noise just start within the last week. And yes the water seems to be gone from tub. The bleace and softner
    issue about a year ago.
    Last edited by kwall139; 11-09-2014 at 11:16 AM.

  4. #4
    Join Date
    Feb 2012
    Location
    Canada
    Posts
    2,348

    Default

    Did you find the model#??
    http://www.applianceaid.com/model-number.php Some model# helps.

    jeff.
    http://www.applianceaid.com/
    Appliance Repair Aid

  5. #5
    Join Date
    Nov 2014
    Posts
    7

    Default

    Sorry about that, Model # is FAV68UOAWW - Ser # is 10433518EE..

    Thanks,

    Korey

  6. #6
    Join Date
    Feb 2012
    Location
    Canada
    Posts
    2,348

    Default

    FAV68UOAWW
    I got FAV6800AWW to work for me.

    It seems that when the setting for spinning (water extracting) the tube makes a noise and the clothes are still wet when spin cycle is complete
    Try the quick spin test...

    Quick Spin Test
    While in Service Mode, press the
    Hand Wash
    key to start a
    Quick Spin
    Test.
    Quick Spin test steps are as follows:
    1) Lock the lid.
    2) Spin to index speed 90 rpm and hold for 60 seconds. Pump drains machine.
    3) Spin to index speed 150 rpm and hold for 6seconds
    4) Spin to index speed 350 rpm and hold for 6 seconds.
    5) Spin to index speed 550 rpm and hold for 6 seconds.
    6) Spin to index speed 700 rpm and hold for 6 seconds.
    7) Spin to index speed 850 rpm and hold for 6 seconds.
    Pump out.
    8)Coast down to 0 rpm chimes 3 times.

    Place a piece of tape on each tumbler ( access from each other ) before starting the spin test. After the spin test, see if the tape are still lined up with each other or are they off-set now.

    Service manual linked below...
    http://www.applianceaid.com/pdf/_docs_16022808.pdf

    jeff.
    http://www.applianceaid.com/
    Appliance Repair Aid

  7. #7
    Join Date
    Nov 2014
    Posts
    7

    Default

    The white round tumblers that are attached to stanless steel tub spin but the tub it self doen't spin, but it does drain the water. I moved the belt below and the tumblers spinned around but not the stainless steel tub. I can't even spin the tub by hand. Also I get no sevice code.

    Korey

  8. #8
    Join Date
    Feb 2012
    Location
    Canada
    Posts
    2,348

    Default

    Place a piece of tape on each tumbler ( access from each other ) before starting the spin test. After the spin test, see if the tape are still lined up with each other or are they off-set now.
    Doing the spin test and checking too see if the tumblers are moving during the spin is checking the see fi the clutch is bad....during spin the tumblers shouldn't move, if they do the clutch is bad.

    I can't even spin the tub by hand
    Trying to turn the wash tub by hand, you normally shouldn't be able to.

    A copy:

    Will Not Spin
    • During fill cycle – If machine tumbles and spins simultaneously replace clutch assembly.
    • During spin cycle – If machine tumbles and spins simultaneously replace clutch assembly.
    • Perform Motor and Motor Control Test.
    • Check belt.
    • Check that the machine control correctly senses all 3water levels are empty. See Board Input Test.
    • Tub Displacement Sensor disconnected, or loose wire.

    Wet Clothes
    • Very small clothes loads can cause unbalanced loads - add additional towels.
    • Excessive suds may have been present.
    • Check Tub Displacement Sensor connection and main harness connector at machine control board.
    • Check Tub Displacement Sensor for 0 to 3.0 Volts DC output voltage between ground and the board input. Check for 12 Volts DC input voltage between the ground and the board output. Only check for voltage at the Tub Displacement Sensor. Do not perform a continuity check. See Tub Displacement Diagnostics
    • Excessive motion was detected in spin Run Quick Spin Test with an empty tub to check Tub Displacement Sensor and machine control board.
    • Check for restricted drain system.

    jeff.
    http://www.applianceaid.com/
    Appliance Repair Aid

  9. #9
    Join Date
    Nov 2014
    Posts
    7

    Default

    Can't spin tub by hand. Belt is attached and I can move it by hand which only tumblers move. Ive checked all connections. Im clueless,,,,,

  10. #10
    Join Date
    Feb 2012
    Location
    Canada
    Posts
    2,348

    Default

    Can't spin tub by hand. Belt is attached and I can move it by hand which only tumblers move.
    Seized tub bearing is possible

    Maytag Neptune TopLoader washing machine water extracting issues-outer-tub-25001199-01646171-jpg LINK> Outer tub includes bearings

    And...

    Maytag Neptune TopLoader washing machine water extracting issues-clutch-12002211-01117050-jpg LINK> Pulley and clutch assembly

    And...

    Maytag Neptune TopLoader washing machine water extracting issues-tub-seal-25001090-00992689-jpg LINK> Tub seal

    jeff.
    http://www.applianceaid.com/
    Appliance Repair Aid

Similar Threads

  1. Neptune Washing Machine MAH4000AWW
    By Not Handy in forum Appliance Repair
    Replies: 3
    Last Post: 01-25-2016, 09:47 PM
  2. GE washing machine won't start
    By DeadDireWolf in forum Appliance Repair
    Replies: 1
    Last Post: 01-13-2016, 08:25 AM
  3. Replies: 2
    Last Post: 10-18-2015, 09:22 PM
  4. Frigidaire Affinity Washing Machine
    By golfschmid@aol.com in forum Appliance Repair
    Replies: 1
    Last Post: 02-27-2015, 09:50 PM
  5. Maytag Ensignia quiet series 200 water temp issues.
    By apnutter in forum Appliance Repair
    Replies: 1
    Last Post: 01-14-2015, 10:31 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •